รายละเอียดสินค้า:
การชำระเงิน:
|
วิธีการควบคุม: | การควบคุมโปรแกรม PLC | ทดสอบความเร็ว: | 10 ± 3mm / นาที |
---|---|---|---|
อำนาจ: | 380v / 50hz | ชื่อผลิตภัณฑ์: | อุปกรณ์ทดสอบเฟอร์นิเจอร์ |
ความเร็วในการหนีบ: | 5-50mm / นาที | มาตรฐาน: | ASTM D6055 |
แสงสูง: | furniture testing equipment,impact testing machine |
เครื่องทดสอบความปลอดภัยเฟอร์นิเจอร์ผลิตภัณฑ์ขนาดใหญ่แพคเกจอุปกรณ์ทดสอบแรงหนีบ
1 Before placing the packaged product between platens, verify that the clamp force using the clamp indicator. ก่อนที่จะวางผลิตภัณฑ์บรรจุภัณฑ์ระหว่างแผ่นรองตรวจสอบว่าแรงยึดโดยใช้ตัวบ่งชี้หนีบ The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens. ควรวางตัวบ่งชี้ระหว่างแกนของจุดประกบของแผ่นแท่นประมาณ 1/2 ทางจนถึงแท่นวาง
2 ทุกครั้งที่ผลิตภัณฑ์ถูกจับยึดควรใช้แรงอย่างน้อย 15 วินาทีและไม่เกิน 1 นาที
3 Apply the clamp force on the sample with the platens resting on the floor and the front edge of the platens flush with the front of the package (see flush platen photo 4). ใช้แรงยึดกับตัวอย่างโดยวางแผ่นที่วางอยู่บนพื้นและขอบด้านหน้าของแผ่นรองจะถูกล้างออกทางด้านหน้าของแพ็คเกจ (ดูที่รูปถ่ายของแผ่นสำหรับล้าง 4) If the package is too large for the clamps to be flush to front edge (ie, large refrigerator, tractor etc.), clamp as close to the edge as possible. หากบรรจุภัณฑ์มีขนาดใหญ่เกินไปสำหรับที่หนีบจะต้องล้างไปที่ขอบด้านหน้า (เช่นตู้เย็นขนาดใหญ่รถแทรกเตอร์ ฯลฯ ) ให้ทำการหนีบให้ใกล้กับขอบมากที่สุด
4 หนีบผลิตภัณฑ์ทั้งหมด 10 ครั้งในทิศทางที่ล้างออก
5 Apply the clamp force on the packaged product with the platens in a 6×6 inch(15.2x15.2cm) offset position(see fig 5 ). ใช้แรงยึดกับผลิตภัณฑ์ที่บรรจุด้วยแท่นวางในตำแหน่งชดเชย 6 × 6 นิ้ว (15.2x15.2 ซม.) (ดูรูปที่ 5) Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. ทั้งขนาดออฟเซ็ตแนวนอนและแนวตั้งถูกวัดที่มุมด้านล่างด้านหน้าของแท่นวาง If the package is too large for the clamp to be positioned 6-inches from the front edge (ie, large refrigerator, tractor etc.), clamp as close to this position as possible. หากหีบห่อมีขนาดใหญ่เกินไปสำหรับแคลมป์ที่จะวางตำแหน่งขนาด 6 นิ้วจากขอบด้านหน้า (เช่นตู้เย็นขนาดใหญ่แทรคเตอร์ ฯลฯ ) ให้หนีบให้อยู่ใกล้กับตำแหน่งนี้มากที่สุด
1) Exception number 1: for large products with an obvious, visible external skid(see fig 6), offset clamp testing is not conducted if the product does not extend beyond any part of the skid and there is some form of handling graphic or note that indicates to clamp only from the skid. 1) หมายเลขข้อยกเว้น 1: สำหรับผลิตภัณฑ์ขนาดใหญ่ที่มีการเลื่อนไถลภายนอกที่ชัดเจนและมองเห็นได้ (ดูรูปที่ 6) การทดสอบแคลมป์ออฟเซตจะไม่ดำเนินการหากผลิตภัณฑ์ไม่ขยายเกินส่วนใด ๆ ของการลื่นไถลและมีรูปแบบการจัดการกราฟิกหรือโน้ต ที่บ่งบอกว่าจะยึดจากลื่นไถลเท่านั้น If there is no graphic or not indicating this or there is some overhang beyond the skid, then the entire clamp test protocol is conducted. หากไม่มีภาพกราฟิกหรือไม่แสดงสิ่งนี้หรือมีสิ่งใดยื่นเกินกว่าการลื่นไถลดังนั้นจึงทำการทดสอบแคลมป์ทดสอบทั้งหมด
2) หมายเลขข้อยกเว้น 2: หากความสูงของผลิตภัณฑ์เมื่ออยู่ในทิศทางการจัดส่งปกติคือ≤ 12 นิ้วจะไม่ทำการทดสอบออฟเซ็ต 6 x 6 นิ้ว
6 หนีบผลิตภัณฑ์ทั้งหมด 10 ครั้งด้วยที่หนีบในตำแหน่งออฟเซ็ต 6 x 6 นิ้ว
7 Repeat step 5.2.5 except with a 2 x6 inch offset clamp position. ทำซ้ำขั้นตอนที่ 5.2.5 ยกเว้นตำแหน่งแคลมป์ 2 x 6 นิ้ว The 2 x6 inch offset is similar to the 6 x6 inch offset except the platens are oriented such that they are 2-inches from the floor and 6-inches back from the package's front edge. ออฟเซ็ต 2 x6 นิ้วคล้ายกับออฟเซ็ต 6 x6 นิ้วยกเว้นแท่นวางจะถูกวางไว้เพื่อให้มีขนาด 2 นิ้วจากพื้นและหลัง 6 นิ้วจากขอบด้านหน้าของแพ็คเกจ If the package is too large for the clamps to be positioned 2-inches from the front edge (ie, large refrigerator, tractor etc.), clamp as close to this position as possible. หากบรรจุภัณฑ์มีขนาดใหญ่เกินไปสำหรับที่หนีบจะต้องอยู่ในตำแหน่ง 2 นิ้วจากขอบด้านหน้า (เช่นตู้เย็นขนาดใหญ่แทรคเตอร์ ฯลฯ ) ให้หนีบให้อยู่ใกล้กับตำแหน่งนี้มากที่สุด
8. . Repeat flush and offset clamping on all other sides of the product that are indicated in the handling graphics as acceptable for clamp handling. ทำซ้ำตัวหนีบฟลัชและออฟเซ็ตที่ด้านอื่น ๆ ของผลิตภัณฑ์ที่ระบุไว้ในกราฟิกการจัดการให้เป็นที่ยอมรับสำหรับการจับยึด
ตามมาตรฐานการตัดสินหากมีรายการใดรายการหนึ่งล้มเหลวในการทดสอบให้หยิบยก“ แผ่นทดสอบการจัดการความล้มเหลว
การป้องกันความปลอดภัย
การป้องกันการโอเวอร์โหลดการป้องกันแรงดันเกินและอุปกรณ์ป้องกันตำแหน่งที่ จำกัด
แรงหนีบ: |
50-3000kg |
ขนาดของคณะกรรมการหนีบ: |
1200 x 1200 มม |
พื้นที่หนีบสูงสุด: |
1200 x 1200 x 1200 มม |
พื้นที่หนีบขั้นต่ำ: |
400 x 1200 x 1200 มม |
ความเร็วหนีบ: |
5-50mm / นาที |
พื้นที่ขึ้นลง: |
100-600mm, ปรับได้, สามารถปรับแต่ง |
ขนาด: 3 |
810 โดย 1900 โดย 2100 |
น้ำหนัก: |
800kg |
พลังงาน: |
380v / 50hz |
ระบบควบคุม: |
การควบคุมโปรแกรม PLC |
ข้อมูลจำเพาะ
เครื่องทดสอบที่หนีบแพคเกจ
1. สูงถึง ASTM D6055
2. การควบคุม PLC
พารามิเตอร์
แรงหนีบ |
1T |
สี |
ไม่จำเป็น |
มติ |
1 / 100,000 |
ทดสอบพื้นที่ (ยาว x กว้าง x สูง) |
100x100 x 100 ซม |
ทดสอบความเร็ว |
10 ± 3mm / นาที |
น้ำหนัก |
ประมาณ 300 กิโลกรัม |
อำนาจ |
1 #, 220V / 50HZ |
ผู้ติดต่อ: Kelly